-
Admin started the topic Training junior for scavenge space cleaning in the forum Main & Aux Engine 6 years, 9 months ago
Firstly before on the important of keeping scavenge space clean, safety and risk acessment as the main priority.
- Prior to entering enclose space, risk assessment to be carry out by competent officer
- Potential hazards to be identified. Such as toxic gas.
- The space have to check for oxygen content using gas detector. Oxygen should read…
-
Admin started the topic Lo managment in the forum Fuel Oil, Lub Oil and Water Treatment 6 years, 9 months ago
1) when taking over duties
– As C/E, upon joining vessel check ROB of all grades of Lo for any difference
– Check the daily consumption
-Check for sufficient Lo for voyage
– Check for Lo analysis
2) Ordering of Lubricant
– Take ROB of grade
-Identify economical port
-Check sounding and how much to be taken <…[Read more]
-
Admin started the topic Max liftable bunker in the forum Miscellaneous 6 years, 9 months ago
If office ask for max liftable bunker, 85% of available tank
- voyage – distance, speed, weather, anchorage, port stay
- vessel – Dead weight tonnage, avoid overloading, draft restriction for cargo calculation
- any interal transfer done for ship stability
- as per company policy, 85% volume, no more than 90%<…
-
Admin started the topic How to take Lub oil sample & batch purification in the forum Fuel Oil, Lub Oil and Water Treatment 6 years, 9 months ago
Explain Sampling Procedure of lube oil?
- Draw samples from a connection that comes directly out of the main oil supply line to the engine.
- Always sample for the same point.
- Sample only when the oil is up to its operating temperature with the engine running.
- Depending upon the draw off point, sufficient amount of oil should be d…
-
Admin started the topic Lub oil properties in the forum Fuel Oil, Lub Oil and Water Treatment 6 years, 9 months ago
Oil is selected to improve the engine operation and reduce the wear down rate and hence the maintenance cost of the machine.
Alkalinity
- When fuel burns, the fumes carry sulphuric acid which can cause acidic corrosion. Four stroke engines, the main lube oil is responsible for piston and liner lubrication; alkalinity of lube oil is impor…
-
Admin started the topic Types of Rudders in the forum Steering Gear, Propeller & Stern tube 6 years, 9 months ago
1. Spade or Balanced Rudder
1) A spade rudder is basically a rudder plate that is fixed to the rudder stock only at the top of the rudder.In other words, the rudder stock (or the axis of the rudder) doesn’t run down along the span of the rudder.
The position of the rudder stock along the chord of the rudder (width meaning, from the for…[Read more]
-
Admin started the topic Pilgrim Nut in the forum Steering Gear, Propeller & Stern tube 6 years, 9 months ago
1) it is to ensure a solid frictional drip between propeller and shaft, the use of pilgrim nut facilitates the transmission of engine torque without using key.
2) Pilgrim nut is basically a hydraulic jack with threads, screwed into slot provided on tail shaft. Propeller is forced onto tapered tail shaft region by using a steel ring, which…[Read more]
-
Admin started the topic Keyless & Controlable pitch propeller in the forum Steering Gear, Propeller & Stern tube 6 years, 9 months ago
The keyway on the shaft taper is a source of defects leading to fatigue cracks developing because of the sudden change on the surface shape leading to stress concentrations around the keyway because of its sharp corners. If the key and keyway are eliminated about 75% of this problem is solved. Hence the need for keyless propeller…[Read more]
-
Admin started the topic Valve positioner in the forum Miscellaneous 6 years, 9 months ago
Valve Hysteresis
It is an undesireable characteristic which affect valve positioning.
Effect is the actuator pressure does not produce the same valve opening
Causes
1) non linearity in actuator force due to varing effective diaphragm area
2) non linearity in valve opening force due to varying opening rate
3) non…[Read more]
-
Admin started the topic Voyage data recorder (VDR) in the forum Miscellaneous 6 years, 9 months ago
1)Akin to the ‘Black Box’ on airplanes, a Voyage Data Recorder is an equipment fitted onboard ships that record the various data on a ship which can be used for reconstruction of the voyage details and vital information during an accident investigation.
Information is stored in a secure and retrievable form, relating to the position, move…[Read more]
-
Admin started the topic Refrigeration plant operational faults in the forum Air/Con & Refrigeration 6 years, 9 months ago
- Loss of Oil from Crankcase
– Operational leakage
– Foaming
– Suction pressure drops rapidly from evaporator
– Compressor running on high capacity (unloading setting)
Action
– Use defoaming agent during prolong shut down
– Shut stop valve in liquid supply line to expansion valve
– Suction and discharge valves to shut…[Read more]
-
Admin started the topic Stern tube, how to change seal insitu in the forum Steering Gear, Propeller & Stern tube 6 years, 9 months ago
To fully prevent oil leakage. #3s added as spare ring
In case of leakage, #3s seal ring is put into operation by close the line valve for #3, #3s will activate
In case of all seal failure,
- Adjust LO pressure of stern tube to equal or higher then sea water pressure by changing the gravity tank position. If seawater leaking in
- If…
-
Admin started the topic Hull protection in the forum Ship Construction & Drydocking 6 years, 9 months ago
Sacrificial Anodic Protection
- Sacrificial anodes work on the principle of electrolysis,
- an anode and a metallic strip are dipped in electrolytic solution,
- Anode electron will dissolve and deposit over the metallic strip and make it a cathode.
- Seawater acts as an electrolyte and transfers the electrons from the anode to the steel…
-
Admin started the topic Air compressor, taking too long to fill & bumping clearances in the forum Main Air Compressor 6 years, 9 months ago
Reasons taking too long to fill up.
- Unloader leaking
- Bottle drain valve or relief valve leaking
- Air consumption increase due to some valve kept open, someone using air continuously, air leakage on pipe/ flange.
factors affecting volumetric efficiency,
- bumping clearance increase
- suction & discharge valves sticky, leaky
…
-
Admin started the topic Boiler repeated flame failure actions in the forum Boilers 6 years, 9 months ago
Possible causes:
-
-
-
- Flame eye dirty
- Pilot burner. ( DO tank empty, do pump not working, nozzle choked, igniter electrode> no voltage, position wrong, fouled or gap too much)
- Air/ fuel ratio incorrect
- Air fuel ratio adjusting linkage incorrect
- ACC failure
-
-
Main burner
- Valve shut
- Filter cho…
-
-
Admin started the topic Types of boiler burners in the forum Boilers 6 years, 9 months ago
Turn down ratio indicates the flexibility of burner to cope with different loads without losing efficiency.
TRD = fuel consumption at max load/ fuel consumption at minimum load.
Pressure jet burner TDR 3:1
Rotary cup TDR 15:1
Steam blast TDR 20:1
Ultrasonic TDR 15:1
- Simple pressure jet burner
Atomization of f…[Read more]
-
Admin started the topic Boiler combustion controller ( ACC) in the forum Boilers 6 years, 9 months ago
- Combustion control system correct the proportion the quantities of air and fuel being burnt.
- Ensure complete combustion
- The system measure the flow rates of fuel oil and air in order to correctly regulate their proportions.
- Two control elements are used, ‘steam flow’ and ‘steam pressure’.
- The steam pressure signal is fed to a c…
-
Admin started the topic Boiler safety valve setting in the forum Boilers 6 years, 9 months ago
Difference between a safety valve and a relief valve
- Relief valve:
The higher the pressure, the more the valve disc lifts off its seat. Relieving capacity increases with over-pressurization increase.
- Safety valve:
Designed to stay completely closed until the popping pressure is reached. At popping point the valve lifts sharply a…[Read more]
-
Admin started the topic Tie rod, Material & tightening procedure in the forum Main & Aux Engine 6 years, 9 months ago
Fitting of new tie rod
- The lower nut of tie rod is screwed on
- Clean the seating surface of intermediate ring and upper nut
- Screw ring screw on tie rod and lift till the lower tie rod rest against the bearing shield
- Tighten the upper tie rod nut with tommy bar until seated firmly, then remove ring screw
Tightening Seq…[Read more]
-
Admin started the topic Turbocharger L & M, surging, how to minimise & sealing arrangment in the forum Main & Aux Engine 6 years, 9 months ago
L & M
K = It is the distance between the compressor end cover mounting face and shaft end .Mark it as K.
Pull the rotor shaft towards the compressor side until the impeller comes in contact with the insert and determine K2.
Impeller clearance L = K – K2
Thrust the rotor shaft towards the turbine side until the turbine disc and…[Read more]
- Load More
